Auto Priming Trash Diesel Driven Centrifugal Pump with Trailer

• Customization: Available
• After-sales Service: Worldwide
• Warranty: 1 Year
• Model NO.: SCP
• Air Engine Type: Diesel Engine
• Theory: Jet-flow
• Transmission: Direct Connection Transmission
• Structure: The Slide
• Flow: up to 2000m3/H
• Head: up to 100m
• Engine: Diesel Engine
• Fluid: Water,Waster Water,Slurry,etc
• Usage: Sewage
• ODM/OEM: Yes
• Transport Package: Wood Case
• Specification: ISO
• Trademark: Borra
• Origin: Wenzhou
• HS Code: 8413810090
• Production Capacity: 500

Product Description

Auto Priming Trash Diesel Driven Centrifugal Pump with Trailer

SCP series of self-priming diesel engine pumps are an ideal dirty water treatment pump for solid particles. The impeller can let solid particles with diameters below 76mm pass. It is easy to use on the ground, finishes the installation and daily maintenance.

Applicable occasions:

areas without power supply; surprise flood prevention and drainage; dirt drain projects, architecture, paper-making, textile, foods, chemicals, electric power distribution, mining, sewage drain, leather, brewage, non-corrosive, and highly-polluted sewage drain.drought relief; agricultural irrigation and aquaculture; various temporary pumping occasions; cofferdam pumping industry, municipal drainage.

1. Preparation before equipment operation
2. Prepare sufficient diesel engine oil, diesel oil, anti-cold fluid (water can also be added depending on the ambient temperature);
3. Prepare the water inlet pipe with flange (suction pipe: steel wire rubber pipe) less than 10 meters, and it can also be equipped with a quick connector to connect the water pump inlet and the water inlet pipe;
4. Prepare the outlet pipe (blue hose, fire hose, or rubber hose);


Conditions, temperature:

0ºC~40 ºC, density≤1.2×10 3 kg/m3, pH: 5~9; solid particle proportion ≤2%;·maximum particle diameter: SCP-3 63mm; SCP-4/SP-6 76mm; ambient temperature:≤40 ºC;·altitude: maximum 1000m.






 Technical Parameters:

	RPM	Q		H
		m3/h	1/s	m	kW	HP	mm	mm	m
SCP-2	1150	15	4.2	4.0	1.1	1.5	50(2')	38	5.0
	1450*	20	5.6	6.5	1.5	2			6.5
	1750	25	6.9	9.5	3	4			6.5
	2050	28	7.8	13.5	4.0	5.5			6.5
	2350	32	8.9	18.0	7.5	10			6.5
	2650	35	9.7	23.0	7.5	10			6.5
	2900*	40	11.1	27.0	9.2	12.5			6.5
SCP-3	650	25	6.9	2	0.75	1	80(3')	63	1.5
	750*	30	8.3	3	1.5	2			1.8
	850	32.5	9.0	4	1.5	2			2.4
	950*	40	11.1	4.5	1.5	2			3.0
	1050	42.5	11.8	5.5	3	4			4.0
	1150	45	12.5	7	4	5.5			4.9
	1250	50	13.9	8	4	5.5			5.5
	1350	52.5	14.6	10	5.5	7.5			5.8
	1450*	55	15.3	11.5	5.5	7.5			6.4
	1550	60	16.7	12.5	7.5	10			6.4
	1650	65	18.1	14.5	11	15			6.7
	1750	70	19.4	16	11	15			6.7
	1850	72.5	20.1	18	15	20			7.6
	1950	75	20.8	20	15	20			7.6
	2050	80	22.2	22.5	18.5	25			7.6
	2150	85	23.6	24.5	18.5	25			7.6
SCP-4	650	40	11.1	3	1.5	2	100(4')	76	1.5
	750*	45	12.5	4	1.5	2			2.4
	850	53	14.7	5	2.2	3			4.9
	950*	60	16.7	6	3	4			5.8
	1050	65	18.1	7.5	5.5	7.5			6.7
	1150	72	20	9	5.5	7.5			7.3
	1250	80	22.2	10.5	7.5	10			7.6
	1350	85	23.6	12.5	11	15			7.6
	1450*	100	27.8	13.5	11	15			7.6
	1550	110	30.6	15.5	15	20			7.6
	1650	115	31.9	18	18.5	25			7.6
	1750	120	33.3	20	22	30			7.6
	1850	130	36.1	22.5	30	40			7.6
	1950	135	37.5	25	30	40			7.6
SCP-6	650	100	27.8	3.5	3	4	150(6')	76	2.4
	750*	125	34.7	4.5	4	5.5			2.7
	850	150	41.7	5.5	7.5	10			3.6
	950*	160	44.4	7.5	7.5	10			4.2
	1050	180	50	9	11	15			5.5
	1150	200	55.6	10	15	20			6.4
	1250	220	61.1	12.5	22	30			6.4
	1350	230	63.9	15	30	40			6.7
	1450*	250	69.4	17	30	40			7.0
	1550	280	77.8	18	37	50			7.6
SCP-8	650	200	55.6	6	7.5	10	200(8')	76	2.7
	750*	230	63.9	8	11	15			3.7
	850	260	72.2	10	15	20			4.6
	950*	300	83.3	12	22	30			5.2
	1050	320	88.9	15	30	41			6.1
	1150	350	97.2	18	37	50			6.4
	1250	400	111.1	20	55	75			6.7
	1350	450	125.0	23	75	102			7
	1450*	500	138.9	26	75	102			7
SCP-10	650	250	69	6.5	11	15	250(10')	76	2.1
	750*	300	83	8.5	15	20			3.4
	850	350	97	11	22	30			4.3
	950*	400	111	13	30	41			5.2
	1050	450	125	16	45	61			5.5
	1150	500	139	19	55	75			5.5
	1250	525	146	23	75	102			5.8
	1350	550	153	27	90	122			6.7
	1450*	600	167	31	90	122			6.7

 Start, running and stop 

Start

1. First of all, pour water into pipes, to make the pump and inlet pipe filled with water. The pipes shall be sealed, no air leaked. (no-water inside start is forbidden) 
2. Close globe valve and cock on outlet pipe, to reduce start currency.
3. Rotate the rotor by hand, lubricate the bearing and check the pump impeller, seal the ring, if it cannot rotate, you shall not start.
4. Try to start, motor rotation direction shall be as same as the arrow direction on the pump. 
5. When the rotor works normally, open gradually the outlet globe valve, adjust for the work conditions required.

Running

1. Observe the reading in meters, keep it running around the flow and head shown on the nameplate.
2. Regularly check, motor currency value shall not exceed rated currency value.
3. Pump bearing temperature shall not exceed 75ºC, and shall not be 35ºC higher than ambient environment.
4. To start, loosen the stuff cap. Adjust later when started.
5. In case of fragile component abrasion, replace in time.
6. When any abnormal happens, immediately stop and check.

Stop

1. Close the globe valve on the outlet pipe, close the vacuum gauge cock.
2. Stop the motor, and close the pressure cock.
3. In Winter, drain the liquid in the pump completely to avoid frozen cracks.
4. When you will not use it for a long time, uninstall the pump, clean, and lubricate.


Troubleshooting 
 

Fault	Cause	Solution
The pump cannot suck water, pressure gauge & vacuum gauge vibrating	1. Insufficient water pouring  2. Leak between pipe and meter  3. Suction is too high	1, check a leak in the bottom valve.  2, Tighten the leaked part  3, reduce suction
The pump cannot suck, high vacuum is shown in the vacuum gauge	1, bottom valve closed or jammed  2, Too great water suction resistance  3, filter jammed	1, check bottom valve 2, replace water suction pipe 3, clear off the filter
Pressure gauge works, no water outcome	1. Great outlet water pipe resistance 2. Wrong rotation direction  3. Outlet pipe valve closed 4. impeller jammed	1. check or shorten water pipe  2, check the motor, adjust  3, open the valve and clear off the impeller
Cannot reach designed flow	1. air sucked  2. Water level drops, submerged depth is not enough  3. impeller jammed  4. rotor torn and worn	1, check leak part and clear off  2, prolong water inlet pipe, increase the submerged depth 3, uninstall and clear off  4, replace seal ring
Great pump power consumption	1. Stuff tightened, overheated  2. Great flow  3. Collision between rotor and case  4. Pump shaft bearing abrasion  5. Pump shaft misplaced	1. loosen slightly 2. reduce globe valve opening 3. adjust  4. replace bearing  5. replace or adjust
Great pump vibration	1. impeller partially jammed  2. impeller damaged  3. little flow  4. non-concentric between pump shaft and motor. 5, bearing damaged  6, gas etching	1. Uninstall and clear off  2, replace  3, increase opening  4, adjust 5, replace   6, change suction inlet position

Borra Technology Co., Ltd.

Borra Technology co., Ltd., founded in 1995, owns a top-rank design, production, sales, and service team, and modern production lines, to manufacture various self-priming pumps, movable diesel pumps, diesel Self-Priming dirt drain pumps, diesel fire pumps units, diesel mini-pumps.
Certificate :



Services:

1. One year or 1000 working hours guarantee of the whole machine except for wear parts;
2. Technical support by email the whole day;
3. Calling service;
4. User's manual available;
5. Installation guide for clients from both China and abroad;
6. Maintenance and replacement service;

FAQ:

Q1: Are you a reliable company?
A1: Bora is located in Wenzu, a beautiful city in Zhejiang Province, China. we have many years of manufacturing experience,
we can supply all types of fire protection solutions, Drainage and sewage solution, and other pump products.
We have an independent factory and trade office.

Q2: how to deliver the portable diesel water pump
A2: We can offer our equipment by containers or bulk ship.

Q3: How to pay for the portable Diesel water pump?
A3: We can accept T/T, L/C and soon

Q4: why choose borra company?
A4: We have an independent factory and foreign trade office. so we can design high-quality portable generators
and water pumps according to clients requirements and our price is reasonable. 

Contact Us
If you are interested in our products or have any questions about our products, we are very honored to serve you.