Diesel Water Pump Diesel Genset Magnetic Water Pump

• Customization: Available
• After-sales Service: Worldwide
• Warranty: 1 Year
• Model NO.: XBC
• Max.Capacity: >400 L/min
• Driving Type: Magnetic
• Impeller Number: Magnetic
• Working Pressure: Middle Pressure Pump
• Influent Type of Impeller: Single Suction Pump
• Position of Pump Shaft: Horizontal Pump
• Pump Casing Combined: Horizontal Split Pumps
• Mounting Height: Suction Centrifugal
• Impeller: Open
• Usage: Pump
• Transport Package: Standard Plywood Case
• Specification: SGS
• Trademark: Borra
• Origin: Wenzhou
• HS Code: 8413709940
• Production Capacity: 1000

Product Description

Magnetic Pump CQB :
The CQB magnetic drive pump is a new type of completely leak-free corrosion-resistant pump developed by the National Joint Design Group of Magnetic Pumps. Its technical and economic indicators are equivalent to those of similar foreign products in the late 1980s. It is a supplement and improvement to the CQ pump.


Main features:

1. an ideal pump for leak-free
2. transport all kinds of corrosive media.
3. The optimized product jointly designed by the national magnetic pump can directly replace the ih type chemical process pump.

Application :

petroleum, chemical, metallurgy, pharmaceutical, electroplating, environmental protection, and other industries, and can transport flammable, explosive, highly toxic, and precious liquids below 100°C. Using the principle of magnetic transmission, no leakage


Pump Body :

The flow part of the pump is made of all stainless steel, which has good corrosion resistance to organic acids, organic compounds, alkali, neutral solutions, and a variety of gases. The double spiral groove carbon graphite bearings and cemented carbide bushings Run-in, with strong wear resistance, to ensure the life of the product.


Condition : 
 

1. Since the cooling and lubrication of the magnetic pump bearing depends on the conveyed medium, idling rotation is prohibited, and at the same time, avoiding idling operation caused by restarting after a power cut in the middle of the work.
2. If the conveyed medium contains solid particles, a filter should be added to the pump inlet: if it contains ferromagnetic particles, a magnetic filter should be added.
3. The ambient temperature of the CQB magnetic drive centrifugal pump during use should be less than 40ºC, and the temperature rise of the motor should not exceed 75ºC.
4. The conveyed medium and its temperature should be within the allowable range of the pump material (see attached table for details). The service temperature of the engineering plastic pump is less than 60ºC, the service temperature of the metal pump is less than 100ºC, the conveying suction pressure is not more than 0.2mpa, the working pressure is 1.6mpa, the density is not more than 1600kg/m3, and the particle size is not more than 30 × 10-6m2/s. Liquid without hard particles and fibers.
5. the medium that is easy to precipitate and crystallize as the conveying liquid, it should be cleaned in time after use, and the liquid accumulated in the pump should be drained.
6. the CQB magnetic pump has been running for 100 hours, the wear of the bearing and the end face moving ring should be disassembled and inspected, and the wearing parts that are not suitable for reuse should be replaced.
7. The internal and external magnetic couplings of CQB-type magnetic drive pumps adopt high-performance permanent magnet materials, which may cause potential harm to the following devices. Please keep the following devices away from this series of pumps. Such as cardiac pacemakers, credit cards, and other magnetic cards, calculators, computer disks, watches, etc.

Technical Parameter :
 

Flow	Up to 100m3/h
Head	Up to 80 m
Speed	2900 RPM
Power	Up to 55 kW
Inner Caliber	Up to 100 mm
Outer Caliber	Up to 65 mm

Troubleshooting :

Fault	Cause	Method of exclusion
no water comes out of the Pump	1-  the water pump reverses 2- Air leakage in the water inlet pipe 3-The voltage is too high, and the coupling slips when starting. 4- the suction lift is too high. 5-the suction lift is too high. 6-the valve does not open.	1-change the motor wiring. 2-Prevent air leakage. 3-Increase the water storage. 4-Adjust the positive voltage. 5-lower the sand installation position. 6-correct or change the valve.
Insufficient flow	1-the suction pipe diameter is too small or blocked.  2- the impeller flow passage is blocked. 3-the head is too high. 4-the speed is not enough.	1-change the inlet pipe. 2-clean the impeller. 3-open the large water outlet valve. 4-recover the rated speed.
Head is too low	1-the flow is too large. 2- the speed is too low.	1-close the small water outlet valve. 2-recover the rated speed.
Too noisy	1- the shaft is severely worn. 2- the shaft sleeve is severely worn. 3- Drive the magnetic steel cup in contact with the isolating sleeve. 4-Grinding of the seal ring and impeller.	1-replace the pump shaft. 2-replace the shaft sleeve. 3-Remove the pump head and reassemble it. 4-Replace thrust ring and seal ring.
Leakage	1- The sealing ring is damaged.	1- Replace the o-shaped sealing ring.

Borra Technology Co., Ltd.


Borra Technology co., Ltd., founded in 1995, owns a top-rank design, production, sales, and service team, and modern production lines, to manufacture various self-priming pumps, movable diesel pumps, diesel Self-Priming dirt drain pumps, diesel fire pumps units, diesel mini-pumps.

Certificate :
Services:

1. One year or 1000 working hours guarantee of the whole machine except for wear parts;
2. Technical support by email the whole day;
3. Calling service;
4. User's manual available;
5. Installation guide for clients from both China and abroad;
6. Maintenance and replacement service;

FAQ:

Q1: Are you a reliable company?
A1: Bora is located in Wenzu, a beautiful city in Zhejiang Province, China. we have many years of manufacturing experience,
we can supply all types of fire protection solutions, Drainage and sewage solution, and other pump products.
We have an independent factory and trade office.

Q2: how to deliver the portable diesel water pump
A2: We can offer our equipment by containers or bulk ship.

Q3: How to pay for the portable Diesel water pump?
A3: We can accept T/T, L/C and soon

Q4: why choose borra company?
A4: We have an independent factory and foreign trade office. so we can design high-quality portable generators
and water pumps according to clients requirements and our price is reasonable. 

Contact Us
If you are interested in our products or have any questions about our products, we are very honored to serve you.